Wolo 7000 SERIES Infinity 1 User Manual download pdf

INFINITY-1 HALOGEN LIGHT BAR

INSTALLATION MANUAL

7000 SERIES

Your purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Wolo’s warning lights

are manufactured with the finest materials. Before it is packaged, each light is tested to meet our high

standards to ensure a perfect working light. Our quality workmanship and components are Wolo’s

assurance that this product will provide years of dependable service. If you need help using your new Wolo

warning lights, our technicians are available to answer your questions, Monday thru Friday, from 9 AM to

4 PM EST at 1-888-550-4676.

Before installation of the light bar is attempted, it is important to read these instructions completely. The lives of

people are dependent on a proper installation of the light bar to the vehicle. The person installing this light bar

must have advanced knowledge of the proper method for mounting and securing the light bar to a vehicle's roof

or exterior as well as knowledge of the vehicle's electrical system. Again, read this manual completely and note

any messages marked “IMPORTANT” or “WARNING’’. A safe installation will prevent serious injury or damage

to the vehicle.

The INFINITY-1 is completely wired and does not require any internal wiring by the installer. The power

cable has all the required wires for a successful installation.

Installation of the INFINITY-1 Light Bar requires drilling to the vehicle. The installer must carefully inspect

both sides of the selected locations to ensure that there are no components, wires and or any other

vehicle part that could be damaged by drilling. IMPORTANT: Always de-burr any drilled holes, ensuring

that there are no sharp edges. Install a rubber grommet into all metal holes that the wires are being

routed through.

Always refer to the vehicle’s shop manual for deployment location of air bags. Never install the light bar's

switch control panel, wires and or components in the deployment area of any air bag. Improper

installation could reduce the effectiveness of the vehicle's air bag system and or project an object that

could cause serious personal injury or death to driver and passenger. The user/installer assumes all

responsibility to properly access a safe mounting location of the light bar's control panel, so to provide

ultimate safety to the driver and passengers inside the vehicle.

This light bar is a high current device. To operate this product at peak performance, the heavy gauge

black wire should always be connected directly to the (-) negative battery post.

The vehicle operator and or maintenance department should inspect the light bar frequently to ensure all

brackets are securely attached to the vehicle and that all mounting hardware is free of corrosion.

The light bar’s control panel should be mounted in a location where the switches can be easily reached.

Never attempt to turn light bar on/off when driving under hazardous conditions.

These installation instructions should always be kept and stored in a safe location so that they can be

referred to when information, maintenance or reinstallation is required.

Failure to follow all safety precautions and installation procedures outlined in these instructions could

result in property damage to the vehicle, serious injury or death to you or others.

MOUNTING LIGHT BAR

1. Place the light bar on the selected location of the vehicle's roof. A preferred mounting position on the

roof is close to the B-pillar, which is the strongest part of the roof. IMPORTANT: Make sure the light

bar is facing the correct direction.

1 2 3 4 5 6

Summary of Contents

Page 1 - 7000 SERIES

INFINITY-1 HALOGEN LIGHT BAR INSTALLATION MANUAL7000 SERIESYour purchase of a Wolo warning light is the perfect choice to compliment your vehicle. Wol

Page 2 - Vehicle’s Roof

2. Make sure the selected location of the lightbar will allow the stainless steel straps toattach to the vehicle window ledge on boththe driver's

Page 3 - SIDE VIEW OF

12. The hook of the stainless steel strap that is secured to the vehicle's window ledge has a hole locatedin the middle. Use the hole as a templ

Page 4 - BULB REPLACEMENT

WIRING21. WARNING: Failure to wire the light barcorrectly could result in permanent damageto the light bar, the vehicle's electricalsystem and/or

Page 5

30. To remove bulb, simply press down and turn counter clockwise. The bulb should easily be able tobe removed from the socket. Dispose the bad bulb o

Page 6 - CLEANING

WarrantyWolo Manufacturing Corporation (“Wolo”) warranties to the original purchaser, for three months from the date of purchase, thatthis product is

Comments to this Manuals

No comments

Wolo 7000 SERIES Infinity 1 User Manual

Browse online or download User Manual for Lighting Wolo 7000 SERIES Infinity 1. Wolo 7000 SERIES Infinity 1 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Lighting Wolo 7000 SERIES Infinity 1